Products

CA03 Add On Short Tee Type Tube Size A B         Kg
CA03 Fitting CA03 Diagram CA03G32 42.4 60 55         0.60
CA03G40 48.3 68 60         0.71
The Add On short Tee allows existing structures to be added to without the need for any dismantling. Tubes must not be jointed within this fitting.
CA40 Add On 90° Crossover Type Tube Size A B         Kg
CA04 Fitting CA40 Diagram CA40G32 42.4 49 46         0.65
CA40G40 48.3 55 50         0.73
The Add On 90° Crossover allows existing structures to be added to
without the need for any dismantling. This fitting is designed to give a 90°
offset crossover joint. Tubes must not be joined within this fitting.
C00 Sleeve Joint Type Tube Size A           Kg
C00 Fitting C00 Diagram C00G20 26.9 76           0.33
C00G25 33.7 89           0.39
C00G32 42.4 102           0.49
C00G40 48.3 100           0.54
C00G50 60.3 120           1.14
The Sleeve Joint is designed to provide an in line joint between two tubes
of the same diameter.
C01 Expanding Connector Type Tube Size A B         Kg
C01 Fitting C01 Diagram C01G25 33.7 75 19         0.25
C01G32 42.4 75 19         0.35
C01G40 48.3 75 19         0.45
The expanding Connector is designed to provide an in line joint between
tubes of the same diameter, and a wall thickness of 3.2mm. It fits flush
with the tube surface and can be located inside other fittings. It must not
be used as a load-bearing joint, in these applications use a FastClamp
type C00.
C02 90° Elbow Type Tube Size A           Kg
C02 Fitting C02 Diagram C02G20 26.9 40           0.28
C02G25 33.7 48           0.39
C02G32 42.4 60           0.55
C02G40 48.3 67           0.65
C02G50 60.3 86           1.04
The 90° Elbow is designed to provide a joint between two tubes at right
angles to each other. Often used for railing ends and corners.
C03 Short Tee Type Tube Size A B         Kg
C03 Fitting 03iagram C03G20 26.9 40 36         0.19
C03G25 33.7 48 48         0.32
C03G32 42.4 60 57         0.44
C03G40 48.3 67 63         0.58
C03G50 60.3 86 75         0.76
The Short Tee is designed to provide a butt joint between two tubes at right
angles to each other. Often used for railing ends and tops. If tubes need to
be joined inside the fitting then a C04G type should be used.
C04 Long Tee Type Tube Size A B         Kg
C04 Fitting C04 Diagram C04G20 26.9 40 80         0.35
C04G25 33.7 48 96         0.56
C04G32 42.4 60 120         0.75
C04G40 48.3 67 134         0.91
C04G50 60.3 86 172         1.40
The Long Tee is designed to provide a butt joint between two tubes at right
angles to each other. Often used for railing ends and tops. It allows the through tube to be joined inside the fitting. An alternative is the C03G type fitting.
C05 Variable Elbow Type Tube Size A B C D     Kg
C05 Fitting C05 Diagram C05G25 33.7 65 60 13 50     0.41
C05G32 42.4 80 66 16 55     0.68
C05G40 48.3 95 75 17 55     0.89
The Variable Elbow is designed to make joints at an angle of between 15° and 60°.
C06 Internal T Joint Type Tube Size A B         Kg
C06 Fitting C06 Diagram C06G25 33.7 34 45         0.39
C06G32 42.4 40 54         0.58
C06G40 48.3 44 60         0.66
The Internal T joint is designed to provide an angled joint between a tube and a FastClamp fitting when used in conjunction with C02G and C03G type fittings. Often used for railing tops and midrails to accommodate a slope as offset railing.
C07 45° Tee Type Tube Size A           Kg
C07 Fitting C07 Diagram C07G25 33.7 45           0.49
C07G32 42.4 54           0.69
C07G40 48.3 60           0.91
The 45° Tee is used as a bracing and strut component for strengthening structures.
C10G Swivel Base Type Tube Size A B C D E   Kg
C10G Fitting C10G Diagram C10G N/A 50 40 50 81 111   0.35
The Swivel Base is designed to provide a base fixing. It is usually used in
conjunction with a C36G type fitting to make a C46G type base swivel
combination. This fitting does not provide sufficient rigidity to be used as
a railing base without other means of support.
C11 Wall Flange Type Tube Size A B C D   Ø Kg
C11 Fitting C11 Diagram C11G20 26.9 86 42 57 4   9 0.32
C11G25 33.7 89 45 64 6   9 0.41
C11G32 42.4 102 50 76 6   9 0.51
C11G40 48.3 114 57 89 6   9 0.64
C11G50 60.3 127 64 95 6   9 1.10
The Wall Flange is designed to provide a positional wall or base fixing.
It is not recommended to use this fitting as a structural railing base.
C12 Railing Base Flange - Ductile Type Tube Size A B C D E Ø Kg
C12 Fitting C12 Diagram C12G20 26.9 76 65 8 76 114 11 0.65
C12G25 33.7 89 76 9 89 128 14 1.01
C12G32 42.4 89 80 10 102 140 14 1.41
C12G40 48.3 89 89 10 114 152 14 1.61
C12G50 60.3 128 88 9 127 165 18 1.80
The Railing Base is designed to provide a base for railings and other structures. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Page
C13 Railing Vertical Side Support Type Tube Size A B C M L Ø Kg
C13 Fitting C13 Diagram C13G25 33.7 45 96 67 25 104 14 0.91
C13G32 42.4 50 109 72 30 114 14 1.20
C13G40 48.3 60 123 86 40 120 14 1.50
The Railing Vertical Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Page.
C14 Railing Horizontal Side Support Type Tube Size A B C     Ø Kg
C14 Fitting C14 Diagram C14G25 33.7 90 30 12     18 0.92
C14G32 42.4 90 35 12     18 1.41
C14G40 48.3 90 41 15     18 1.53
The Railing Horizontal Side Support is designed to provide a base for
railings and other structures that need a side mounted fixing. It is
recommended that this fitting be used in accordance with FastClamp
maximum post centre dimensions, see table 3 on our Technical Page.
C15 Side Palm Fixing Type Tube Size A B C K L N Kg
C15 Fitting C15 Diagram C15G25 33.7 97 76 63 26 89 71 0.65
C15G32 42.4 108 84 72 31 98 82 0.82
C15G40 48.3 112 92 78 34 104 86 0.86
The Side Support is designed to provide a base for railings and other
structures that need a side mounted xing. It is recommended that this
fitting be used in accordance with FastClamp maximum post centre
dimensions, see table 3 on our Technical Page.
C16 Handrail Bracket Type Tube Size A C E L   Ø Kg
C16 Fitting C16 Diagram C16G20 26.9 44 57 55 78   9 0.45
C16G25 33.7 44 63 57 82   11 0.49
C16G32 42.4 44 76 63 102   11 0.60
C16G40 48.3 48 85 67 108   11 0.63
The Handrail Bracket is designed to secure handrail tube to a wall. It can
also be used on top of walls as a xing for a low rail.
C17 Ground Support Type Tube Size A B C D     Kg
C17 Fitting C17 Diagram C17G25 33.7 60 140 130 4.5     1.42
C17G32 42.4 60 140 130 4.5     1.42
C17G40 48.3 60 140 130 4.5     1.42
The Ground Socket is designed to provide a base that can be cast into the
ground to support a post. The post is removable. It is recommended that
this fitting be used in accordance with FastClamp maximum post centre
dimensions, see table 3 on our Technical Page.
C18 Base Flange - Intergrated Toeboard Type Tube Size A B C D E Ø Kg
C18 Fitting C18 Diagram C18G32 42.4 45 90 58 30 100 18 2.00
C18G40 48.3 45 90 58 30 100 18 2.12
The Base Flange with Integrated Toeboard is ideal for guardrailing and
balustrading applications where the addition of a toeboard is required.
The side plates have slotted holes to allow for a degree of sideways
movement for ease of installation. It is recommended that this fitting be
used in accordance with FastClamp maximum post centre dimensions,
see table 3 on our Technical Page.
C20 3 Way 90° Elbow Type Tube Size A           Kg
C20 Fitting C20 Diagram C20G20 26.9 40           0.37
C20G25 33.7 48           0.53
C20G32 42.4 61           0.80
C20G40 48.3 67           1.02
C20G50 60.3 84           1.82
The 3 way 90° Elbow is designed to provide a neat corner for the upper rail of guardrail or frames.
C21 Corner C/W Through Tube Type Tube Size A L         Kg
C21 Fitting C21 Diagram C21G20 26.9 40 36         0.26
C21G25 33.7 48 48         0.43
C21G32 42.4 60 57         0.58
C21G40 48.3 67 63         0.69
C21G50 60.3 86 75         1.70
The Corner Complete with through tube is designed to provide a 90°
corner for the intermediate rail of guardrail or frames.
C22 Two Socket Cross Type Tube Size A B         Kg
C22 Image C22 Diagram C22G20 26.9 40 80         0.36
C22G25 33.7 48 95         0.43
C22G32 42.4 60 120         0.62
C22G40 48.3 67 134         0.71
C22G50 60.3 86 172         1.50
The Two Socket Cross fitting provides the midrail joint for handrail and
other structures. It is recommended that the handrail post is continuous
through the fitting.
C23 Side Outlet Cross Type Tube Size A L         Kg
C23 Fitting C23 Diagram C23G20 26.9 40 44         0.42
C23G25 33.7 48 48         0.49
C23G32 42.4 60 57         0.94
C23G40 48.3 67 63         0.88
C23G50 60.3 86 75         1.67
The Side Outlet Tee fitting provides a three way midrail joint for handrail
and other structures. It is recommended that the handrail post is
continuous through the fitting.
C24 4 Way Cross + Central Tube Type Tube Size A L         Kg
C24 Fitting C24 Diagram C24G20 26.9 41 59         0.60
C24G25 33.7 48 65         0.84
C24G32 42.4 60 80         1.21
C24G40 48.3 67 85         1.20
C24G50 60.3 86 90         2.50
The 4 Way Cross tting provides a four way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting. This fitting may also be used for the top rail with the centre post capped with a C65 Plastic Stop End.
C25 Short Tee Swivel Type Tube Size A           Kg
C25 Fitting C25 Diagram C25G20 26.9 65           0.31
C25G25 33.7 66           0.32
C25G32 42.4 73           0.45
C25G40 48.3 81           0.49
C25G50 60.3 110           1.14
Short Tee Swivel fittings are normally used in pairs to facilitate corner angles of 90° to 180°, it is also used on staircases with a C02 and C03 fittings in conjunction with a short piece of tube and a C65 Plastic Stop End in landing areas. When ordering please specify the number of fittings required, not the number of pairs.
C26 Angle Cross up to 45° Type Tube Size A           Kg
C26 Fitting C26 Diagram C26G25 33.7 162           0.87
C26G32 42.4 190           1.20
C26G40 48.3 218           1.51
Typically used for Guardrail when connecting the mid or lower rails to uprights. The upright tube must remain continuous with the mid and lower rails cut to suit. The C26 is normally used in conjunction with aC27. Fittings are stocked as blamks and are machined to the customer's specified angle between 0° and 45°.
C27 Angle Tee up to 45° Type Tube Size A           Kg
C27 Fitting C27 Diagram C27G25 33.7 162           0.91
C27G32 42.4 190           1.31
C27G40 48.3 218        
Typically used for Guardrail when connecting top rails to uprights. The C27 is normally used in conjunction with aC26. Fittings are stocked as blamks and are machined to the customer's specified angle between 0° and 45°.
C28 Adjustable 2 Socket Cross 30°- 45° Type Tube Size A           Kg
C28 Fitting C28 Diagram C28G25 33.7 162           0.82
C28G32 42.4 190           1.17
C28G40 48.3 218           1.50
The Adjustable 2 Socket Cross fitting will accommodate any rake angle from 30° to 45°. This fitting is not recommended as the top fitting on a guardrail or balustrade system, use the C29 Adjustable Short Tee.
C29 Adjustable Short Tee %140" bgcolor="#6D6E71">Tube Size A L         Kg
C29 Fitting C29 Diagram C29G25 33.7 74 54         0.58
C29G32 42.4 85 63         0.87
C29G40 48.3 102 68         0.90
The Adjustable Short Tee fitting will accommodate any rake angle from 30° to 60°. This fitting is commonly used for the top rail of handrail to accommodate the rake angle on slopes. It can also be used for any Tee Joint that needs to mate at an angle of between 30° and 60° for light weight structures.
C30 Collar Type Tube Size A           Kg
C30 Fitting C30 Diagram C30G20 26.9 22           0.15
C30G25 33.7 25           0.15
C30G32 42.)E0Ϣ@\Q}imli©k\r(Ppss="table_black">          0.18
C30G40 48.3 25           0.21
C30G50 60.3 40           0.31
The Collar fitting can be used to support the C03 fitting when the latter is used as a hinge. It can also be used to increase the load capacity of another fitting when used together. This tting can be used as a stop for a sliding tube.
)ETҢ@8Q}imli©k6\r(PB
C31 Gate Eye Type Tube Size A B C       Kg
C31 Fitting C31 Diagram C31G20 26.9 25 30 15       0.21
C31G25 33.7 25 33 15       0.2342.4 25 38 15       0.25
C31G40 48.3 25 41 15       0.29
This fitting is designed as a gate eye for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.
C32 Gate Hinge Type Tube Size A B C D     Kg
C32 Fitting C32 Diagram C32G20 26.9 30 25 13 38     0.24
C32G25 33.7 33 25 13 38     0.27
C32G32 42.4 38 25 13 38     0.30
C32G40 48.3 41 25 13 38     0.33
This fitting is designed as a gate hinge for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.
C33 Hook Type Tube Size A B C D     Kg
C33 Fitting C33 Diagram 26.9 32 25 10 25     0.17
C33G25 33.7 34 25 13 21     0.25
C33G32 42.4 39 25 13 25     0.25
C33G40 48.3 41 25 13 25     0.30
The fitting is designed to provide an attachment for chain.
)Eڢ@Q}imli©kώ\r(P3 border="0" cellpadding="0" cellspacing="0">
C34 Fixing Pad Type Tube Size A B C     Ø Kg
C34 Fitting C34 Diagram C34G25 26.9 45 25 5     6 0.18
C34G32 33.7 53 40 5     11 0.34
C34G40 42.4 56 40 5     11 0.37
The fitting is designed to provide an attachment for flat sheets or board. It may also be used as a gate stop. An alternative fitting for the attachment of boards is the C35 type.
C35 Male Swivel Type Tube Size A B C     Ø Kg
C35 Fitting C35 Diagram C35G20 26.9 32 38 5     6 0.18
C35G25 33.7 32 42 5     6 0.20
C35G32 42.4 32 47 5     6 0.21
C35G40 48.3 32 50 5     6 0.24
C35G50 60.3 48 60 5     6 0.53
The Male Swivel can be used on its own for use with a shakle and chain or with the C36 female swivel to mount rails at any angle for slopes. It can also be used for attaching flat sheets or boards to a structure and is available assembled with the C36 fittings as a C45 single swivel combination.
C36F Female Swivel Type Tube Size A B C D     Kg
C36F Fitting C36F Diagram C36G25F 33.7 41 35 60 10     0.35
C36G32F 42.4 44 35 63 10     0.41
C36G40F 48.3 50 35 70 10     0.49
The Female Swivel is designed as part of the swivel combination group of fittings. It can be used with the C10, C35, C37, C38 or C39 male swivel fittings.
C36M Male Swivel Type Tube Size A B         Kg
C36M Fitting C36M Diagram C36G20M 26.9 36 58         0.25
C36G25M 33.7 30 60         0.36
C36G32M 42.4 40 70         0.48
C36G40M 48.3 45 75         0.58
C36G50M 60.3 58 95         0.95
The Male Swivel is designed as part of the swivel combination group of fittings. It can be used with C36F fittings.
C37 Double Male Swivel Type Tube Size A B       Ø Kg
C37 Fitting C37 Diagram C37G20 26.9 40 32       10 0.27
C37G25 33.7 44 32       10 0.28
C37G32 42.4 49 32       10 0.34
C37G40 48.3 52 32       10 0.35
C37G50 60.3 63 50       10 0.63
The Double Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings. The double swivel combination is also available assembled as a type C47 fitting.
C38 90° Corner Male Swivel Type Tube Size A B C     Ø Kg
C38 Fitting C38 Diagram C38G20 26.9 40 39 8     10 0.28
C38G25 33.7 44 38 8     10 0.30
C38G32 42.4 49 48 8     10 0.34
C38G40 48.3 53 48 8     10 0.38
The 90° Corner Male swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings to make a corner combination fitting which is also available assembled as a type C48 type fitting.
C40 90° Crossover Type Tube Size A B         Kg
C40 Fitting C40 Diagram C40G20 26.9 36 35         0.20
C40G25 33.7 40 40         0.36
C40G32 42.4 45 50         0.41
C40G40 48.3 51 56         0.56
C40G50 60.3 61 64         1.06
C40G25-32 33.7 / 42.4 45 45         0.46
C40G25-40 33.7 / 48.3 51 48         0.50
C40G32-40 42.2 / 48.3 51 52         0.59
The 90° Crossover connects two rails at 90° to each other and is often used for the handrailing when continuous standard lengths of tube are used. Please note that tube joints should use the C00 or C01 type fitting and not the C40 type fitting.
C41 Clamp On Tee Type Tube Size A B         Kg
C41 Fitting C41 Diagram C41G20 26.9 50 25         0.35
C41G25 33.7 53 25         0.45
C41G32 42.4 67 35         0.65
C41G40 48.3 77 35         0.70
C41G50 60.3 90 45         1.20
The Clamp on Tee is designed to allow an new tube to be joined to an existing structure. Torque maximum 15N\M. This uses an M10 stainless steel bolt
C42 Clamp On Crossover Type Tube Size A B C D     Kg
C42 Fitting C42 Diagram C42G20 26.9 37 28 27 27     0.18
C42G25 33.7 44 34 34 34     0.30
C42G32 42.4 53 43 43 43     0.47
C42G40 48.3 58 49 49 49     0.65
C42G50 60.3 70 62 61 61     0.81
The Clamp on Cross over is designed to allow a new tube to be joined to an existing structure.
C43 Combination Socket Type Tube Size A B C       Kg
C43 Fitting C43 Diagram C43G20 26.9 31 35 40       0.30
C43G25 33.7 42 40 48       0.57
C43G32 42.4 54 50 60       0.79
C43G40 48.3 60 56 67       0.96
C43G50 60.3 72 68 86       1.65
The Combination Socket is designed for racking and similar systems to allow a crossover to be combined with a cross tie.
C45 Single Swivel Combination Type Tube Size             Kg
C45 Fitting C45 Diagram C45G20 26.9             0.48
C45G25 33.7             0.60
C45G32 42.4             0.71
C45G40 48.3             0.86
C45G50 60.3             1.47
The Single Swivel Combination is designed to provide and angled tee between two tubes. It can be used to construct sloping handrail and for providing bracing struts to structures.
C46 Base Swivel Combination Type Tube Size             Kg
C46 Fitting C46 Diagram C46G20 26.9             0.64
C46G25 33.7             0.77
C46G32 42.4             0.94
C46G40 48.3             0.98
C46G50 60.3             1.29
The Base Swivel Combination is designed to provide an angled wall or floor mounting. This fitting should not be used as a railing base without suitable support.
C47 Double Swivel Combination Type Tube Size             Kg
C47 Fitting C47 Diagram C47G20 26.9             0.90
C47G25 33.7             1.06
C47G32 42.4             1.25
C47G40 48.3             1.45
C47G50 60.3             2.50
The Double Swivel Combination is designed to provide an in line angled joint as a post, this is suitable for the mid rail of a sloping handrail or to provide bracing to a structure.
C48 90° Corner Swivel Combination Type Tube Size             Kg
C48 Fitting C48 Diagram C48G20 26.9             0.90
C48G25 33.7             1.06
C48G32 42.4             1.29
C48G40 48.3             1.50
The 90° Corner Swivel Combination is designed to provide an angled joint at a post, this is suitable for the mid rail of sloping handrail or to provide bracing to a structure.
C50 Slope Elbow 0° to 11° Type Tube Size A           Kg
C50 Fitting C50 Diagram C50G32 42.4 60           0.87
C50G40 48.3 67           1.02
The Slope Elbow is designed to provide an elbow for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
C51 Short Slope Tee 0° to 11° Type Tube Size A B         Kg
C51 Fitting C51 Diagram C51G32 42.4 68 60         0.62
C51G40 48.3 72 68         0.76
The Slope Short Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
C52 Slope Long Tee 0° to 11° Type Tube Size A B         Kg
C52 Fitting C52 Diagram C52G32 42.2 144 60         1.02
C52G40 48.3 159 67         1.01
The Slope Long Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
C53 Slope Base 0° to 11° Type Tube Size A B C D E Ø Kg
C53 Fitting C53 Diagram C53G32 42.2 91 140 79 102 10 14 0.90
C53G40 48.3 96 152 80 114 10 14 1.40
The Slope Base is designed to provide a base for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
C54 Slope 2 Socket Cross 0° to 11° Type Tube Size A B         Kg
C54 Fitting C54 Diagram C54G32 42.4 144 72         0.93
C54G40 48.3 158 79         1.00
The Slope 2 Socket Cross is designed to provide a joint for the midrail for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
C55 27½°Ridge Fitting Type Tube Size A B       Kg
C55 Fitting C55 Diagram C55G40 48.3 67 89         0.96
A four way socket fitting used to construct the ridge of a roof structure.
C56 27½° Eaves Fitting Type Tube Size A B C D     Kg
C56 Fitting C56 Diagram C56G40 48.3 67 89 83 51     1.19
A four way socket fitting used to construct the eaves of a roof structure.
C60 Spare Screws Type Tube Size              
C60 Screws Blank Image C60S25 26.9 & 33.7              
C60S32/40 42.4, 48.3 & 60.3              
Spare screws come in two sizes, 1/4" BSP for the 20 and 25nb range and 3/8" BSP for the 32, 40 and 50 rangess.
C61 Allen Keys Type Tube Size              
C61 Allen Keys Blank Image C61S25 26.9 & 33.7              
C61S32/40 42.4, 48.3 & 60.3              
Allen keys are available in two sizes, the first is suitable for the 20 ans 25nb fitting and the other for the 32, 40 and 50nb fittings..
C62R Ratchet Keys Type Tube Size              
C62R Ratchet Keys Blank Image C62R ALL SIZES              
The ratchet driver and dual keys are also available to speed assembly. The ratchet driver will also allow tightening to the correct torque.
C65P Plastic End Cap Type Tube Size             Kg
C65P Plastic End Cap C65P Diagram C65P20 26.9             0.08
C65P25 33.7             0.10
C65P32 42.4             0.10
C65P40 48.3             0.16
C65P50 60.3             0.24
Plastic End Caps are available for finishing plain end tubes. Available in grey plastic they will fit medium and heavy gauge tube.
C65G Metal End Cap Type Tube Size             Kg
C65G Metal End Cap C65G Diagram C65G20 26.9             0.05
C65G25 33.7             0.10
C65G32 42.4             0.12
C65G40 48.3             0.17
C65G50 60.3             0.29
This metal plug is hard to remove once it has been driven in. Note this metal insert can only be used in conjunction with tube with a wall thickness of 3.2mm. There is an alternative plastic version, look at our C65P above.
C66 Single Mesh Clip Type Tube Size A B C       Kg
C66 Fitting C66 Diagram C66G20 26.9 27 26 58       0.06
C66G25 33.7 30 26 61       0.07
C66G32 42.4 33 26 64       0.08
C66G40 48.3 38 26 68       0.09
C66G50 60.3 44 26 75       0.09
The Single Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips be spaced at a maximum of 450mm apart.
C67 Double Mesh Clip Type Tube Size A B C       Kg
C67 Fitting C67 Diagram C67G20 26.9 27 26 58       0.09
C67G25 33.7 30 26 61       0.12
C67G32 42.4 33 26 64       0.13
C67G40 48.3 38 26 68       0.13
C67G50 60.3 44 26 75       0.14
The Double Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips be spaced at a maximum of 450mm apart.
C68 Weather Cowl Type Tube Size A B H       Kg
C68 Fitting C68 Diagram C68G20 33.7 140 25 125       0.25
C68G25 42.4 150 25 150       0.30
C68G40 48.3 166 25 150       0.35
The Weather Cowl is designed to cover the Railing base and provides a weather proof seal when used with a suitable flexible sealant.
C69 Square Plastic End Cap Type Tube Size B C         Kg
C69 Square Plastic Cap C69 Diagram C69P40X40 40x40SHS 40 3.2         0.01
C69P50X50 60X60SHS 50 3.2         0.01
C69P70X70 70X70SHS 70 3.2         0.02
The Plastic End Caps are available for finishing plain end square tubes. Available in grey plastic they will fit medium and heavy tube gauges.
C70 Crimp Straight Type Tube Size AØ B         Kg
C70 Fitting C70 Diagram C70G25 33.7 26.0 34.0         0.27
Straight Crimp Joints provide a permanent in-line connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary and these are available for hire or purchase.
C71 Crimp Elbow Type Tube Size AØ           Kg
C71 Fitting C71 Diagram C71G25 33.7 26.0           0.47
Crimp Elbow's provide a permanent 90° connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary and these are available for hire or purchase.
DDA01 Upright Connector Type Tube Size A B C       Kg
DDA01 Fitting DDA01 Diagram DDA01   55 48.3 40       0.38
A connector used in conjunction with types DDA02 and DDA04 to provide a connection to the upright tube.
DDA02 Handrail Connector Type Tube Size A B C D     Kg
DDA02 Fitting DDA02 Diagram DDA02   51 86 30 38     0.48
When terminating handrailing at an end upright this connector is used in conjunction with types DDA01 and DDA07.
DDA03 Wall Bracket Type Tube Size A B C D E   Kg
DDA03 Fitting DDA03 Diagram DDA03 42.4 88 82 90 8 84   0.62
This wall mounted cradle bracket has two holes to secure the handrail suitable for self tapping screws or pop rivets, and three wall fixing holes suitable for 6mm diameter countersunk screws.
DDA04 Intermediate Bracket Type Tube Size A B C D E   Kg
DDA04 Fitting DDA04 Diagram DDA04 42.4 30 81 84 38 88   0.44
This upright mounted cradle bracket has two holes to secure the handrail suitable for self tapping screws or pop rivets, used in conjunction with type DDA01.
DDA05 End Return Type Tube Size A B C D E   Kg
DDA05 Fitting DDA05 Diagram DDA05 42.4 90 82 8 86 46   0.64
A bracket suitable for terminating handrailing back to a wall with three 6mm diameter countersunk screws, used in conjunction with type DDA07
DDA06 90° Bend Type Tube Size A B C       Kg
DDA06 Fitting DDA06 Diagram DDA06 42.4 33.7 35 50       0.93
An elbow used to create a 90°change of direction whilst retaining a smooth continuous line.
DDA07 Expanding Connector Type Tube Size A B C       Kg
DDA07 Fitting DDA07 Diagram DDA07 42.4 75 19         0.35
Type DDA07 provides an inline handrail joint whilst retaining a smooth continuous line.
DDA08 Plastic End Cap Type Tube Size A           Kg
DDA08 Fitting DDA08 Diagram DDA08   48.3           0.016
This fitting caps the open end top of each upright.
DDA09 Adjustable Bend Type Tube Size A B         Kg
DDA09 Fitting DDA09 Diagram DDA09   31 86         0.61
An adjustable elbow which creates variable direction changes whilst retaining a smooth continuous line, used in conjunction with type DDA07.